1、飼料攪拌機http://m.weijunkj.cn/停機前后在物料壓制即將結束時，將少許麥皮拌合食用油并投入機器內，壓制1-2分鐘后停機，使模具孔內充滿油料，以便下次開機就能投料生產，既保養模具，又節約工時，停機后松動壓輪調節螺絲，并清除殘余料。
Feed mixer before pressing down at the end of the material, a little oatmeal to mix oil and put into the machine,pressed for 1-2 minutes after the shutdown of the die hole filled with oil, so the next boot will be able to feed production, both maintenance mold, and save hours of work, after the shutdown pressure roller adjustment screw loose, and remove residual material.
2、飼料攪拌機壓輪與傳動部分的維護與保養，物料中的硬雜物質或金屬塊應予以清除，可在機器進料口設置永磁筒、或除鐵器，以免影響壓輪、模具和中心軸的使用壽命。由于顆粒料在擠壓過程中溫度高達50-85℃，并且壓輪在運轉工作時承受較強的被動力，但又缺乏必要的、有效的粉塵保護裝置，所以每隔2-5個工作日，必須清洗一次軸承，并加入耐高溫油脂，主軸每隔一個月清洗加油一次，齒輪箱間隔半年就要進行清洗保養，傳動部分的螺絲緊固更換應隨時進行。
Feed mixer pressure wheel and the transmission part of care and maintenance, materials or substances in miscellaneous hard piece of metal should be removed, to set up a permanent magnet material inlet tube, or separator in the machine,
so as not to affect the pressure roller, the mold and the central axis life. Since the pellets during extrusion temperatures up to 50-85 ℃, and pressure roller is subjected to a strong work force in operation, but the lack of necessary and effective dust protection device, so every 2-5 days It must be cleaned once a bearing, and add high-temperature grease, cleaning grease once a month spindle, gear box, cleaning and maintenance intervals will be carried out every six
months, part of the fastening screw drive replacement should be carried out at any time.
3、飼料攪拌機模具的更換方法，壓輪磨損后，可以更換壓輪皮或更換成套壓輪；發現軸承松動、抱死，應更換軸承或連軸一起換掉。環模顆粒機的環模老化、磨損、受傷后，松動抱箍卡盤，換上新的即可；若是螺絲固定類型，須先輕輕振動磨具，然后均勻用力卸掉螺絲，就能更換新的磨具。設別的模板一般都是反扣螺母、鍵槽固定，而且在模板靠內孔附近有兩個對稱的螺絲孔，用螺絲慢慢頂出或用拉力器、拆卸鐵均勻用力拉出即可。注意在頂出或拉出過程中，要用錘子輕輕振動模板，防止螺絲斷在孔內。
Replacement of feed mixer mold, wear pressure after the round, you can replace the pressure roller sets of leather or replace pressure roller; bearings found loose, lock, replace bearings or couplings replace together. Ring mold particles machine ring mold aging, wear, after the injury, loose hoop chuck and put a new can; if screw type, must first shaking gently abrasive, then even force remove screws, can be replaced the new abrasive. Flip the other templates provided are generally nuts, keyway fixed, and in the vicinity of the hole template by two symmetrical screw holes, with the top of the screw slowly or Rally, disassemble the iron even forced to pull it out. Note that at the top or pulling out the process, use a hammer to gently vibrating the template to prevent the screws off in the hole.
4、飼料攪拌機http://m.weijunkj.cn/整機維護，飼料攪拌機要按說明使用配套動力。過小，產量低、效果差；過大，浪費機電、加速機械磨損、縮短使用壽命。維護保養要在斷電狀態下進行。機器應放在適宜工作的地方。盡可能減少搬動次數。常檢修、防水浸、防雨淋、防漏電、防火、防止使用霉變飼料。
Feed mixer machine maintenance, feed mixer according to package instructions use force. Too small, low yields, poor results; too large, mechanical and electrical waste, accelerated mechanical wear, and shorten life. Maintenance to be
carried out in the off state. The machine should be placed in a suitable place to work. Minimize the number of moving. Regular maintenance, water immersion, rain, leakage power, fire, prevent the use of moldy feed.